Assembly instructions · 41 steps
Legs · Waist · Torso · Cockpit · Torso top · Torso to legs · Arms · Base
Legs · Steps 1–8
Step 1
Press a ball joint (53) into each socket (52), then seat both sockets into the feet (51 and 50).
Parts: 53 ×2 · 52 ×2 · 51 · 50
Step 2
Fit the lower legs onto the ball joints: 44 onto foot 51, 43 onto foot 50.
Parts: 44 · 43
Step 3
Attach a vent plate (45) to the front of each lower leg.
Parts: 45 ×2
Step 4
Insert a pin (47) into each knee ring (46), then mount the rings on top of the lower legs.
Parts: 46 ×2 · 47 ×2
Step 5
Slide the thighs onto the knee rings: 42 on the left leg, 41 on the right.
Parts: 42 · 41
Step 6
Lock each knee with a pin (48) pushed through, capped at both ends with plugs (49).
Parts: 49 ×4 · 48 ×2
Step 7
Build the pelvis. On each side of 33, stack a collar (36), ball joint (35) and end cap (34).
Parts: 33 · 36 ×2 · 35 ×2 · 34 ×2
Step 8
Push both legs onto the hip ball joints of the pelvis.
Parts: No new parts
Waist · Step 9
Step 9
Place the locking ring (40) into the waist ring (38) and set it into the top of the pelvis.
Parts: 40 · 38
Torso · Steps 10–15
Step 10
Join the two torso halves (02 and 01) with four connector pins (12).
Parts: 02 · 01 · 12 ×4
Step 11
Fit the vent panels on the front: 13 on the upper pair, 14 on the lower pair.
Parts: 13 ×2 · 14 ×2
Step 12
Attach the grille panels 15 and 16 to the lower sides of the torso.
Parts: 15 · 16
Step 13
Insert the two small pegs (09) into the side of the torso.
Parts: 09 ×2
Step 14
Add the front detail pieces 05, 06, 07 and 08.
Parts: 05 · 06 · 07 · 08
Step 15
Fit the upper bracket (61) and the two side frames (60) into the cockpit opening.
Parts: 61 · 60 ×2
Cockpit · Steps 16–21
Step 16
Drop the pilot seat (22) into the cockpit shell (03) and add the console piece (19).
Parts: 22 · 19 · 03
Step 17
Prepare the canopy glass (04).
Canopy glass can be printed in transparent filament or cut by hand using the provided template.
Parts: 04
Step 18
Set the glass panel (21) behind the canopy frame (20).
Parts: 20 · 21
Step 19
Hinge the finished canopy onto the top of the cockpit.
Parts: No new parts
Step 20
Attach the chin piece (59) under the cockpit.
Parts: 59
Step 21
Insert the cockpit into the front opening of the torso.
Parts: No new parts
Torso top · Steps 22–26
Step 22
Lay the top armor plate (10) onto the torso.
Parts: 10
Step 23
Add the raised spine plate (11) on top of the armor.
Parts: 11
Step 24
Choose the antenna (17) or the cover plug (18) for the socket on top.
Install either the antenna or the cover plug, not both.
Parts: 17 · 18
Step 25
Insert your chosen antenna or plug into the socket.
Parts: 17/18
Step 26
Fill the launcher (62) with ten missile heads (54), then mount it on the rear of the torso top.
Parts: 62 · 54 ×10
Torso to legs · Steps 27–28
Step 27
Under the torso, fit the waist pin (39) and the turning ring (37).
Parts: 39 · 37
Step 28
Lower the torso onto the waist of the leg assembly.
Parts: No new parts
Arms · Steps 29–37
Step 29
Each forearm (56) takes either a cannon barrel (57) or a port cover (58).
Mount either the cannon barrel or the port cover on each arm.
Parts: 56 ×2 · 57 ×2 · 58 ×2
Step 30
Push the barrels or covers into the front of both forearms.
Parts: 57/58 ×2 · 56 ×2
Step 31
Insert two pegs (55) into the back of each forearm.
Parts: 55 ×4
Step 32
Attach the elbow blocks: 67 on one arm, 25 on the other.
Parts: 67 · 25
Step 33
Insert a pin (27) into each elbow ring (28) and mount the rings on the elbow blocks.
Parts: 28 ×2 · 27 ×2
Step 34
Fit the upper arms onto the elbow rings: 24 on one side, 23 on the other.
Parts: 24 · 23
Step 35
Lock each elbow with a pin (26) and an end cap (29).
Parts: 26 ×2 · 29 ×2
Step 36
On each shoulder of the torso, stack a collar (32), ball joint (30) and cap (31).
Parts: 32 ×2 · 30 ×2 · 31 ×2
Step 37
Push both arms onto the shoulder ball joints.
Parts: No new parts
Base · Steps 38–41
Step 38
Pick one front base plate (63).
Three variants: V1 with the DIRE WOLF nameplate, V2 with a blank nameplate, V3 plain.
Parts: 63_V1 · 63_V2 · 63_V3
Step 39
Join base sections 65 and 64 with two connector pins (66).
Parts: 65 · 64 · 66 ×2
Step 40
Attach your chosen front plate (63) with four more connector pins (66).
Parts: 63 · 66 ×4
Step 41
Set the finished Dire Wolf onto the base pegs.
Parts: No new parts
