Assembly instructions · 39 steps
Legs · Cockpit · Torso · Arms · Final assembly
Legs · Steps 1–11
Step 1
Join the shin (36) to the foot (42) with the ball joint (41).
Parts: 36 · 41 · 42
Step 2
Fit the thigh (34) onto the shin and push the hip pin (37) into it.
Parts: 37 · 34
Step 3
Get the joint tool (40) ready.
Part 40, shown in green, is a joint tool that makes assembly easier. It is not part of the finished model.
Parts: 40
Step 4
Use the tool (40) to screw the threaded cap (39) into the knee joint.
Parts: 39 · 40
Step 5
Push the ball joint (32) into one side of the hip (29) and cap it with the ring (31).
Parts: 29 · 32 · 31
Step 6
Attach the first leg to the hip.
Parts: No new parts
Step 7
Build the second leg: join the shin (35) to the foot (42) with a ball joint (41).
Parts: 35 · 41 · 42
Step 8
Fit the thigh (33) onto the shin and push in the hip pin (37).
Parts: 33 · 37
Step 9
Screw the threaded cap (38) into the knee joint with the tool.
Parts: 38
Step 10
Push a ball joint (32) into the other side of the hip and cap it with the ring (31).
Parts: 31 · 32
Step 11
Attach the second leg to the hip.
Parts: No new parts
Cockpit · Steps 12–22
Step 12
Fit the console (14) into the cockpit floor (20).
Parts: 14 · 20
Step 13
Add the side consoles 17 and 18 and the pilot seat (19).
Parts: 17 · 19 · 18
Step 14
Fit the roll cage (21) over the seat.
Parts: 21
Step 15
Attach the rear tank packs 15 and 16.
Parts: 15 · 16
Step 16
Slide the cockpit into the hull (01).
Parts: 01
Step 17
Attach the side pods: two of part 55 on one side, two of part 56 on the other.
Parts: 55 ×2 · 56 ×2
Step 18
Fit the chin plate (59) to the front of the hull.
Parts: 59
Step 19
Fit the side covers 57 and 58 and the top hatch (22).
Parts: 57 · 22 · 58
Step 20
Fit the canopy glass 05, 06 and 07 into the canopy frame (04).
Parts shown in gray are the clear pieces.
Parts: 04 · 05 · 06 · 07
Step 21
Fit the side glass 08, 09, 10 and 11, 12, 13.
Parts shown in gray are the clear pieces.
Parts: 08 · 09 · 10 · 11 · 12 · 13
Step 22
Set the finished canopy onto the cockpit.
Parts: No new parts
Torso · Steps 23–29
Step 23
Join the cockpit to the torso box (02) with the connector plate (03).
Parts: 03 · 02
Step 24
Insert the three vents (45) into the back of the torso.
Parts: 45 ×3
Step 25
Fit the top cover (24) onto the torso.
Parts: 24
Step 26
Build the pod mount: push barrels 46 and 48 into the mount (23) and cap them with 47 and 49.
Parts: 23 · 46 · 48 · 47 · 49
Step 27
Insert two pegs (50) into the top of the mount.
Parts: 50 ×2
Step 28
Attach the missile pods 53 and 54 to both ends of the mount.
Parts: 53 · 54
Step 29
Set the pod assembly onto the torso.
Parts: No new parts
Arms · Steps 30–35
Step 30
Slide the barrel (52) into the arm (43) and add the cap (44).
Parts: 52 · 43 · 44
Step 31
On one side of the torso, fit the shoulder ring (26), push in the ball joint (28) and cap it (27).
Parts: 26 · 28 · 27
Step 32
Attach the first arm to the shoulder.
Parts: No new parts
Step 33
Build the second arm: slide the barrel (51) into the arm (44) and add the cap (66).
Parts: 51 · 44 · 66
Step 34
On the other side, fit the shoulder ring (25), ball joint (28) and cap (27).
Parts: 25 · 28 · 27
Step 35
Attach the second arm to the shoulder.
Parts: No new parts
Final assembly · Steps 36–39
Step 36
Join the upper body to the legs with the pin (30).
Parts: 30
Step 37
Join the base sections 60, 61, 62 and 63 with four connectors (65).
Parts: 60 · 61 · 62 · 63 · 65 ×4
Step 38
Attach the nameplate (64) to the front of the base.
Parts: 64
Step 39
Set the finished MadCat MK II onto the base.
Parts: No new parts
