Assembly instructions · 33 steps
Torso · Hips · Legs · Arms · Pods & antenna · Base
Torso · Steps 1–10
Step 1
Join your chosen cockpit (16 or 15) to the torso core (17) with three pins (46).
Parts: 16/15 · 17 · 46 ×3
Step 2
Pick a cockpit variant.
Two options: part 16 is solid, part 15 has window openings.
Parts: No new parts
Step 3
Fit the window pieces into the cockpit openings.
This step is for the windowed cockpit (15). Parts shown in gray are the clear pieces.
Parts: 40 · 41 · 53 · 39 · 45 · 44 · 38 · 42
Step 4
Insert the chin gun (07) under the nose.
Parts: 07
Step 5
Attach the side brackets 23 and 24 to the torso.
Parts: 23 · 24
Step 6
Attach the side gun (22) to one side of the torso.
Parts: 22
Step 7
Attach the second side gun (21) to the other side.
Parts: 21
Step 8
Fit the vent panel (19) on one side.
Parts: 19
Step 9
Fit the vent panel (20) on the other side.
Parts: 20
Step 10
Close the back of the torso with the rear panel (18).
Parts: 18
Hips · Steps 11–12
Step 11
Insert the lock ring (13) and pin (14) into the hip block (12).
Parts: 12 · 13 · 14
Step 12
Lower the torso onto the hip pin.
Parts: No new parts
Legs · Steps 13–20
Step 13
Build an ankle joint: push the ball (06) into the socket (04) and cap it with the ring (05).
Repeat once for the second ankle.
Parts: 05 ×2 · 06 ×2 · 04 ×2
Step 14
Join the foot (01), ankle joint and shin (03).
Parts: 01 · 03
Step 15
Attach the thigh (08) to the knee.
Parts: 08
Step 16
Push a ball joint (09) into the top of the thigh and cap it with the hip ring (11).
Parts: 09 · 11
Step 17
Build the second leg: foot (01), ankle joint and shin (02).
Parts: 01 · 02
Step 18
Attach the thigh (07) to the knee.
Parts: 07
Step 19
Push a ball joint (09) into the thigh and cap it with the hip ring (10).
Parts: 09 · 10
Step 20
Attach both legs to the sides of the hips.
Parts: No new parts
Arms · Steps 21–28
Step 21
Slide the barrel (32) into the forearm (33).
Parts: 32 · 33
Step 22
Fit the elbow (34) onto the forearm, then lock it with the pin (30).
Parts: 34 · 30
Step 23
Join the shoulder (35) to the elbow with a pin (46).
Parts: 35 · 46
Step 24
Attach the arm to the side of the torso with a pin (46).
Parts: 46
Step 25
Slide the barrel (27) into the second forearm (28).
Parts: 27 · 28
Step 26
Fit the second elbow onto the forearm and lock it with a pin (30).
Parts: 30
Step 27
Join the second shoulder to the elbow with a pin (46).
Parts: 46
Step 28
Attach the second arm to the torso with a pin (46).
Parts: 46
Pods & antenna · Steps 29–30
Step 29
Mount the missile pods 36 and 37 on top of the shoulders.
Parts: 36 · 37
Step 30
Insert the antenna (26) into the top of the torso.
Parts: 26
Base · Steps 31–33
Step 31
Join the two base halves 47 and 48.
Parts: 47 · 48
Step 32
Attach the nameplate (49) to the front of the base.
Parts: 49
Step 33
Set the finished Timber Wolf onto the base.
Parts: No new parts
